P.T. Mativenga

• Artículos de revistas (13)

• Artículos de revistas

  • On the contribution of primary deformation zone-generated chip temperature to heat partition in machining.

    M. Fahad, P.T. Mativenga, M.A. Sheikh

    International journal of advanced manufacturing technology, ISSN 0268-3768, Vol. 68, Nº. 1-4, 2013, págs. 99-110

    

  • Wear mechanisms analysis for turning Ti-6Al-4V�towards the development of suitable tool coatings.

    S.H.I. Jaffery, P.T. Mativenga

    International journal of advanced manufacturing technology, ISSN 0268-3768, Vol. 58, Nº. 5-8, 2012, págs. 479-494

    

  • Assessment of machining performance using the wear map approach in micro-drilling.

    M. Imran, P.T. Mativenga, P.J. Withers

    International journal of advanced manufacturing technology, ISSN 0268-3768, Vol. 59, Nº. 1-4, 2012, págs. 119-126

    

  • Mechanical microdrilling of negative-tapered laser-predrilled holes: a new approach for burr minimization.

    M.M. Okasha, N. Driver, P.T. Mativenga, L. Li

    International journal of advanced manufacturing technology, ISSN 0268-3768, Vol. 61, Nº. 1-4, 2012, págs. 213-226

    

  • A comparative study of multilayer and functionally graded coated tools in high-speed machining.

    M. Fahad, P.T. Mativenga, M.A. Sheikh

    International journal of advanced manufacturing technology, ISSN 0268-3768, Vol. 62, Nº. 1-4, 2012, págs. 43-58

    

  • Evaluation of surface integrity in micro drilling process for nickel-based superalloy.

    M. Imran, P.T. Mativenga, A. Gholinia, P.J. Withers

    International journal of advanced manufacturing technology, ISSN 0268-3768, Vol. 55, Nº. 5-8, 2011, págs. 465-476

    

  • Chip formation in microscale milling and correlation with acoustic emission signal.

    A.J. Mian, N. Driver, P.T. Mativenga

    International journal of advanced manufacturing technology, ISSN 0268-3768, Vol. 56, Nº. 1-4, 2011, págs. 63-78

    

  • An experimental and coupled thermo-mechanical finite element study of heat partition effects in machining.

    F. Akbar, P.T. Mativenga, M.A. Sheikh

    International journal of advanced manufacturing technology, ISSN 0268-3768, Vol. 46, Nº. 5-8, 2010, págs. 491-508

    

  • A comparative study of material phase effects on micro-machinability of multiphase materials.

    A.J. Mian, N. Driver, P.T. Mativenga

    International journal of advanced manufacturing technology, ISSN 0268-3768, Vol. 50, Nº. 1-4, 2010, págs. 163-174

    

  • Assessment of the machinability of Ti-6Al-4V alloy using the wear map approach.

    S.I. Jaffery, P.T. Mativenga

    International journal of advanced manufacturing technology, ISSN 0268-3768, Vol. 40, Nº. 7-8, 2009, págs. 687-696

    

  • A comparative study of the tool�chip contact length in turning of two engineering alloys for a wide range of cutting speeds.

    S.A. Iqbal, P.T. Mativenga, M.A. Sheikh

    International journal of advanced manufacturing technology, ISSN 0268-3768, Vol. 42, Nº. 1-2, 2009, págs. 30-40

    

  • Laser removal of TiN from coated carbide substrate.

    M. Sundar, P.T. Mativenga, L. Li, P.L. Crouse

    International journal of advanced manufacturing technology, ISSN 0268-3768, Vol. 45, Nº. 11-12, 2009, págs. 1169-1178

    

  • White layer formation and hardening effects in hard turning of H13 tool with CrTiAIN and CrTiAIN/MoST-coated carbide tools.

    A. Aramcharoen, P.T. Mativenga

    International journal of advanced manufacturing technology, ISSN 0268-3768, Vol. 36, Nº. 7-8, 2008, págs. 650-657

    

Esta página recoge referencias bibliográficas de materiales disponibles en los fondos de las Bibliotecas que participan en Dialnet. En ningún caso se trata de una página que recoja la producción bibliográfica de un autor de manera exhaustiva. Nos gustaría que los datos aparecieran de la manera más correcta posible, de manera que si detecta algún error en la información que facilitamos, puede hacernos llegar su Sugerencia / Errata.