International journal of advanced manufacturing technology

• 

  Año 2013, Vol. 68, Número 1-4

  • Understanding the process parameter interactions in multiple-pass ultra-narrow-gap laser welding of thick-section stainless steels.

    A.S. Elmesalamy, L. Li, J.A. Francis

    págs. 1-17

    

  • Effect of pulse frequency on microstructure and properties of Ti-6Al-4V by ultrahigh-frequency pulse gas tungsten arc welding.

    Mingxuan Yang, Bojin Qi, Baoqiang Cong

    págs. 19-31

    

  • Identifying the directions of a set of 2D contours for additive manufacturing process planning.

    Neri Volpato, Alexandre Franzoni

    págs. 33-43

    

  • Grasping force controller for parallel grip with fuzzy rules emulated networks.

    Chidentree Treesatayapun

    págs. 45-55

    

  • Solving reverse logistics vehicle routing problems with time windows.

    Sally Kasem, Mingyuan Chen

    págs. 57-68

    

  • One-dimensional multipulse laser machining of structural alumina: evolution of surface topography.

    Hitesh D. Vora

    págs. 69-83

    

  • Finite element modeling of heat transfer in single and multilayered deposits of Ni-WC produced by the laser-based powder deposition process.

    Prabu Balu, Syed Hamid, Radovan Kovacevic

    págs. 85-98

    

  • On the contribution of primary deformation zone-generated chip temperature to heat partition in machining.

    M. Fahad, P.T. Mativenga, M.A. Sheikh

    págs. 99-110

    

  • Assessment of non-uniform shrinkage in the laser sintering of polymer materials.

    S.P. Soe, D.R. Eyers, R. Setchi

    págs. 111-125

    

  • Artificial neural network prediction of weld distortion rectification using a travelling induction coil.

    C. J. Barclay, S. W. Campbell

    págs. 127-140

    

  • Modelling human performance within an automotive engine assembly line.

    Qian Wang, Martin Sowden, Antony R. Mileham

    págs. 141-148

    

  • Propagation of assembly errors in multitasking machines by the homogenous matrix method.

    E. Díaz-Tena, U. Ugalde

    págs. 149-164

    

  • The optimal design of micro end mill for milling SKD61 tool steel.

    Chen Chi-Hsiang, Wang Yung-Cheng

    págs. 165-173

    

  • Effects of tool diameters on the residual stress and distortion induced by milling of thin-walled part

    Xiaohui Jiang, Beizhi Li, Jianguo Yang

    • Resumen

    págs. 175-186

    

  • Machining deformation prediction for frame components considering multifactor coupling effects.

    Z.T. Tang, T. Yu, Q. Xu, Z.Q. Liu

    págs. 187-196

    

  • ANN-based prediction of surface and hole quality in drilling of AISI D2 cold work tool steel.

    Sitki Akincioglu, Faruk Mendi, Adem Çiçek

    págs. 197-207

    

  • Laser-arc hybrid welding of wrought to selective laser molten stainless steel.

    Giuseppe Casalino, Sabina Luisa Campanelli

    págs. 209-216

    

  • Algorithm for the generation of mandrel protection curve and trajectory scheme for spinning machine.

    Qihang Wang, Lei Wang, Zhiwei Jiang

    págs. 217-226

    

  • Effect of roughness geometry on friction during micro V-die bending by using finite element method.

    Daw-Kwei Leu

    págs. 227-240

    

  • Electric hot incremental forming of low carbon steel sheet: accuracy improvement.

    Xiaofan Shi, L. Gao, Hosein Khalatbari

    págs. 241-247

    

  • Preparation mechanism and grinding performance of single-layer self-lubrication brazed CBN abrasive wheels.

    W.F. Ding, Q. Miao, J.H. Xu, Z.Z. Chen

    págs. 249-255

    

  • Modeling of on-line measurement for rolling the rings with blank size errors in vertical hot ring rolling process.

    Xiaokai Wang, Lin Hua

    págs. 257-262

    

  • The effect of tube material, microstructure, and heat treatment on process responses of tube hydroforming without axial force.

    A. Fatemi, M.R. Morovvati, F.R. Biglari

    págs. 263-276

    

  • Friction stir welding of AZ61A magnesium alloy.

    S. Rajakumar, A. Razalrose

    págs. 277-292

    

  • Studies on fracture toughness of cold wire addition in narrow groove submerged arc welding process.

    M. Ramakrishnan, K. Padmanaban

    • Resumen

    págs. 293-316

    

  • A hybrid GA-PSO approach for reliability optimization in redundancy allocation problem.

    M. Sheikhalishahi, V. Ebrahimipour, H. Shiri

    págs. 317-338

    

  • Prediction of quality responses in micro-EDM process using an adaptive neuro-fuzzy inference system (ANFIS) model.

    X. Hyacinth Suganthi, U. Natarajan

    págs. 339-347

    

  • An efficient DEA method for ranking woven fabric defects in textile manufacturing.

    Reza G. Saeidi, Gholam R. Amin

    págs. 349-354

    

  • Supplier evaluation and selection with QFD and FAHP in a pharmaceutical company.

    Alireza Alinezad, Azadeh Seif

    págs. 355-364

    

  • A numeric investigation of friction behaviors along tool/chip interface in nanometric machining of a single crystal copper structure.

    Chunhui Ji, Jing Shi, Yachao Wang

    págs. 365-374