Contributions to the determination of thermal behaviour of façades using quantitative internal irt(infrared thermography)
- Autores: Blanca Tejedor Herrán
- Directores de la Tesis: Miquel Casals Casanova (dir. tes.), Xavier Roca Ramón (codir. tes.)
- Lectura: En la Universitat Politècnica de Catalunya (UPC) ( España ) en 2019
- Idioma: español
- Tribunal Calificador de la Tesis: Alberto Giretti (presid.), Santiago Gasso Domingo (secret.), Alexandre Labasse (voc.)
- Programa de doctorado: Programa de Doctorado en Ingeniería Ambiental por la Universidad Politécnica de Catalunya
- Materias:
- Texto completo no disponible (Saber más ...)
- Resumen
Within the European framework, most of residential buildings do not satisfy the minimum thermal specifications. In fact, the renovation rate across the EU is estimated at 1% per year. To fulfil with the goals stated by European Directives 2010/31/EU and 2012/27/EU, it is necessary to ensure a minimum energy performance gap. From a thorough literature review, it was detected that the thermal behavior of a building is often underestimated or neglected during its construction and operation stages. For this reason, an accurate non-destructive testing (NDT) should be required, improving the shortcomings given by the current modelling tools and diagnostic techniques. The purpose of this thesis was to develop a method for determining in-situ the thermal behavior of façades under steady-state conditions using quantitative internal infrared thermography (IRT). After drawing up a numerical model to estimate the thermal transmittance (U-value) as a key parameter of the built quality, the dissertation continued with a validation process that was executed in two typical Spanish walls from different construction periods. This allowed: (i) refining the proposed method; (ii) exploring the boundaries conditions; (iii) assessing the influence of tabulated values set by international standards for wall emissivity and convective heat transfer coefficients among other aspects. The results revealed lower deviations related to the theoretical U-values (1.24 to 3.97%) for test durations of 2-3 hours. Furthermore, the results demonstrated that the use of tabulated values might entail high deviations (40%) in heavy multi-leaf walls with low U-values. Broadly, construction project documents for existing buildings, especially the oldest ones, are not available. Hence, this method may provide information about the building envelope for future refurbishment. In the case of new buildings, the method might allow the thermal behaviour of building façades to be checked according to the design parameters. Despite this, a subsequent literature review highlighted that a gap in the standardization of this method for in-situ building diagnostics is still to fill. Considering this aspect, three studies were developed in order to enhance the applicability of the quantitative internal IRT within the construction industry field. Firstly, the most influential operating conditions were analyzed through an experimental room with a heavy single-leaf wall tested under a wide temperature difference range (3.8 < DT < 21ºC). Secondly, this dissertation performed tests in a public housing stock comprised of four unoccupied buildings (without electric and heating systems in operation), to assess the influence of non-transient thermophysical properties of the wall (i.e. heat capacity per unit of area) on the accuracy of the method. Thirdly, a data-processing method based on U-value time series analysis was proposed and validated through six building façades with heavy multi-leaf walls. The aim was to find a common criterion for stopping the test when it is not necessary more data to obtain a reliable result. Having investigated the aspects mentioned above, it can be extrapolated that: (i) the optimum temperature difference range is found to be between 7 and 16ºC; (ii) the variance in the thermal transmittance could mainly be predicted by changes in the outer air temperature; (iii) the quantitative internal IRT is more accurate in heavy multi-leaf walls with high heat capacities per unit of area, reaching maximum deviations of 0.20%; (iv) the test might be executed in only 30 minutes; (v) the method could allow the assessment of aspects related to the determination of U-value of unoccupied buildings for DT under 10ºC, especially in Spain or European countries with a Mediterranean climate where these test conditions might represent a limitation. Hence, the decision-making could be streamlined in real built environments, increasing the European renovation rate in the mid-term.
