Ayuda
Ir al contenido

Dialnet


A finite element-based approach for the analysis and design of 3D reinforced concrete elements and its applications to D-regions

  • Autores: Carlos Meléndez Gimeno
  • Directores de la Tesis: Luis Pallarés Rubio (dir. tes.), Pedro Miguel Sosa (dir. tes.)
  • Lectura: En la Universitat Politècnica de València ( España ) en 2017
  • Idioma: español
  • Tribunal Calificador de la Tesis: Miguel Angel Fernández Prada (presid.), Alejandro Pérez Caldentey (secret.), Miguel Fernández Ruiz (voc.)
  • Materias:
  • Enlaces
    • Tesis en acceso abierto en: RiuNet
  • Resumen
    • The finite element method is a powerful analysis tool which has facilitated a better understanding of the behaviour of reinforced concrete structures. Its use in the research field is widespread and complements experimental tests and the development of new analytical models. Its application in practice engineering has permitted to deal with complex elements. However, the general structural engineer is still reluctant to consider finite element modelling for his work as he finds most of these models excessively sophisticated for his needs and knowledge. In particular, complexity of many finite element tools usually derives from the adoption of advanced concrete constitutive models. Implementation of more simple models based on engineering practice could facilitate its use by less experienced finite element users.

      In structural engineering practice finite element analysis can be of great usefulness to deal with those more problematic elements and/or where the application of traditional analysis methods presents limitations. This includes the so-called D-regions with a 3D behaviour. The strut-and-tie method and the stress field method are consistent and rational tools for the analysis and design of D-regions, but while their application to 2D elements is well covered in literature, its extension to 3D is problematic. This generally explains why excessively conservative assumptions are still common in the design of these elements. Refinement of current analytical and design approaches or the use of finite element analysis could lead to more rational solutions which in turn will reduce material requirements and costs.

      A 3D nonlinear finite element-based tool was developed in this thesis oriented towards the analysis and design of 3D D-regions by less experienced finite element users. Regarding material modelling, an orthotropic concrete model was adopted to permit the use of uniaxial stress-strain relationships. Only one single parameter, the uniaxial compressive strength of concrete, needs to be defined. Additionally, several aid functions were implemented, among which the following can be highlighted: a comprehensive, embedded reinforcement model to facilitate the introduction of complex rebar geometries; special support and load elements permitting an integrated and simple treatment of the boundary conditions imposed by them; and a simple design algorithm for the automatic determination of the required rebar areas.

      Three examples of applications to representative 3D D-regions are presented to show the capabilities of the tool. In particular, the analyses of fourteen four-pile caps, three socket base column-to-foundations connections and one anchorage block are described in the third part of the thesis. Results prove that realistic response predictions can be obtained considering relatively simple constitutive models. The capacity of the tool to configure consistent stress field models depending on the reinforcement arrangement is also demonstrated. The generation of rational reinforcement configurations by applying the implemented design algorithm is also shown.

      A strut-and-tie-based method for the analysis and design of four-pile caps with rectangular geometries is proposed in the fourth part. The method is based on a refined 3D strut-and-tie model and the consideration of three potential modes of failure: exceeding the reinforcement strength, crushing of the diagonal strut at the base of the column with narrowing of the strut and splitting of the diagonal strut due to transverse cracking. The main innovation is that the strut inclination is not fixed as in current strut-and-tie-based design procedures, but determined by maximizing the pile cap strength. The method accounts for strength softening of cracked concrete, compatibility constraints and reinforcement details. Its application to 162 specimens of literature led to very good predictions of the ultimate strength and, to a lesser extent, of the mode of failure.


Fundación Dialnet

Dialnet Plus

  • Más información sobre Dialnet Plus

Opciones de compartir

Opciones de entorno