Synthesis and characterization of new polymer electrolytes to use in fuel cells fed with bio-alcohols
- Autores: Soraya Carmen Sánchez Ballester
- Directores de la Tesis: Vicente Soria Sanchis (dir. tes.), Amparo Ribes Greus (dir. tes.)
- Lectura: En la Universitat Politècnica de València ( España ) en 2017
- Idioma: español
- Tribunal Calificador de la Tesis: Josep Maria Salla Tarragó (presid.), Ferrán Martí (secret.), Ozlem Sel (voc.)
- Materias:
- Enlaces
- Tesis en acceso abierto en: RiuNet
- Resumen
Poly(vinyl alcohol) (PVA)-based membranes have gathered significant interest because of their film forming ability and low cost. These films are usually crosslinked to provide a macromolecular network with high dimensional stability. PVA can be modified by introduction of sulfonic acid groups (sPVA) contributing to increase its proton conductivity. In addition, the preparation of hybrid organic-inorganic composite membranes by the addition of graphene oxide (GO) as nano-filler not only reinforces the matrix but also decreases the permeability of solvents. All this has motivated the use of these materials for the preparation of proton exchange membranes (PEMs) for direct methanol fuel cell (DMFC) applications.
Contribution I presents the chemical schemes followed for the bi-sulfonation of the PVA, the synthesis of GO and the preparation of PVA/GO and sPVA/GO composite membranes. In addition, a structural, morphological, thermal, and mechanical characterization of the starting materials and the composite membranes were performed. Finally, in order to evaluate the suitability of the prepared PEMs in fuel cells, the prot cond. was evaluated at room temperature. The results showed that the addition of GO (1 wt.%) into the sPVA matrix, 30sPVA/GO membrane, enhance by 89% the prot cond. compared to its homologue membrane, 30sPVA, free-standing of GO.
In Contribution II, the proton conductive properties of the previously prepared membranes were investigated as a function of the structural (bi-sulfonation) and morphological (crosslinking and addition of GO) modifications. The bi-sulfonated membrane reinforced with GO, 30sPVA/GO, stands out over the rest. The addition of GO improves considerably its prot cond. (20.96 mS/cm at 90 °C) and its maximum power density (Pmax) in the H2-O2 fuel cell test (13.9 mW/cm2 at 25 ºC).
In Contribution III was studied the effect of a new variable, the sufonation of the GO (sGO), on the functional properties of the composites PVA/sGO and sPVA/sGO for DMFC applications. In addition, the results were compared to that obtained for the previously described PVA/GO and sPVA/GO composites. The results conclude that, contrary to expectations, the multiple sulfonation of the 30sPVA/sGO composite strongly reduces the prot cond. (5.22 mS/cm at 50 °C) compared to its homologue 30sPVA/GO (8.42 mS/cm at 50 °C), despite its higher values of ion exchange capacity (IEC). Finally, the 30PVA/sGO composite (1.85 mW/cm2) shows a significant improvement of the DMFC performance (50 °C, 4M methanol solution) compared to the 30sPVA/GO composite (1.00 mW/cm2).
The Layer-by-Layer (LbL) assembly method was used in Contribution IV for the preparation of composite membranes assembled via hydrogen bonding interactions. To do this, GO/PVA and GO/sPVA bilayers were deposited on the surface of 15PVA and 15sPVA substrate membranes, respectively. The composites were denoted as 15PVA(GO/PVA)n and 15sPVA(GO/sPVA)n where n is the number of deposited bilayers, in our case n ranges between 1 and 3. Finally, the potential of the composite membranes for DMFC applications were evaluated, showing the best performance the 15sPVA(GO/sPVA)1 composite.
Finally, the Contribution V was focused on the preparation of composite membranes by LbL Assembly method, but in this case the assembly forces were electrostatic interactions. The GO was dispersed in a poly(allyl amine hydrochloride) solution (GO-PAH) in order to obtain a positively charged solution. The composites were assembled by alternate deposition of GO-PAH and sPVA layers on the surface of 15PVA and 15sPVA substrates, obtaining as a result the composites 15PVA(GO-PAH/sPVA)n and 15sPVA(GO-PAH/sPVA)n. The best value of prot cond. (8.26 mS/cm at 90 °C) was obtained for the 15PVA(GO-PAH/sPVA)1 composite, almost twice that the value obtained for its homologue sulfonated composite 15sPVA(GO-PAH/sPVA)1 (4.96 mS/cm a 90 °C).
